Rheomix ® 125 (BINDER ® 5)

Rheomix ® 125 (BINDER ® 5)


Based Acrylic Dispersion, Surface and Material Contributions fiaplar Enhancer for adherence and Resistance

Description: BINDER ® 5, acrylic dispersion based, in plaster and screed additives used to increase adherence with the impermeable material.

Public Works Pos No: 04.6131-i

End Use:

• Internal - outdoors, vertical and horizontal applications,
• Mortar, plaster and alum in
• prepared for repair mortar is used as the adhesion contribution.

In plaster mortar:

Of reinforced concrete silos, water tanks, pools, water treatment plants and water impermeability of the interior and exterior plaster increase in the adhesion is used as additives.

fiaplarda P.C.C. (Polymer Cement Concrete) Primer on the old concrete or new concrete screed applications, to prevent the formation of cold joints, and is used to increase adherence.

Technical Specifications

Structure of Materials: Modified acrylic dispersion
Color: White
Solids: 42%
Density: ~ 1.08 kg / liter
Applicable Soil Temperature: +5 ° C +35 ° C
Service Temperature: -20 ° C +80 ° C

Above +23 ° C and 50% relative humidity values are given for. High temperatures can shorten the duration of low temperatures will extend.

fiaplarda: 2 cm thick, foot and mouth, even to obtain high adhesion and cracking of surfaces;
In industrial ground to powder, and water impermeability against cracking of 10/33 with in improving MELMENT ® L is used.

Coating of mortar: Foreign places of natural stone, brick, tile, mortar plates prepared for laying of Freezing - Resolution of cycles are used as additives to be impressed.

Scattering Surface preparation: Smooth surface finish concrete surfaces or gas concrete, plaster and ceramic applications before, with the aim of increasing adherence in plaster spreaders are used.

Benefits

* Powerful and creates a permanent bond.
* Excellent adhesion and provides isolation.
* Water, oil and increases resistance to salt solutions.
* Freezing - thawing cycle will increase the durability.
* By increasing the tensile strength in bending large areas reduces the stresses.
* Desc shrinkage cracks and allows non-hardening.
* Soap provides becoming resistance, do not contain additives that cause corrosion.

Application Procedure

Surface Preparation: Cement based surfaces robust, carrier, should be considered to be dust-free and clean. Surface adherence zayışatacak any oil, grease, rust and paraffin remains to be cleaned thoroughly. The edges are created by breaking the surface as possible should be cut perpendicular, equipment must be cleaned of rust, new equipment must be added if necessary.If there is surface water discharge must be drained or be closed with an appropriate plug. The surface water 12 hours before free water on the surface but should not be fed.

Mixing: BINDER ® 5, the application method is diluted with water in proportions specified in the mix.

In plaster mortar: Suitable for gradasyondaki 1 m3 washed river sand is mixed with 350 kg of cement. 5 kg to 120 kg of water in the liquid mixture prepared with the addition BINDER ® 5, the powder mixture prepared in the mortar on the trowel to obtain until the consistency is added.Surfaces should be wet before applying 12 hours ago, BINDER ® 5 blended mortar, wet / dry surface should be applied.

fiaplarda P.C.C. (Polymer Cement Concrete) Primer: new concrete over old concrete or screed applications to prevent the formation of cold joints, and is used to increase aderansın. A: 1 kg of cement and 3 kg (0 - 3 mm threaded) washed river sand is mixed. B: 1 kg BINDER ® 5, 2 kg is mixed with water. Mixtures A and B are mixed boza facing to consistency. The mixture, brush with 2 mm thick over 12 hours once soaked the surface is applied to pose. P.C.C. on the fresh concrete must be placed before drying, PCC'nin should not be allowed to dry. Dry P.C.C. Once applied on a new floor, and the second floor on the fresh concrete yerleştirilir.Bir total consumption is 0.35 kg/m2.

FIAP Construction: Suitable washed river sand gradasyondaki 1 m3 at least 350 kg of cement is mixed. 4 kg to 110 kg of water in the liquid mixture prepared with the addition BINDER ® 5, the powder mixture prepared upon suitable primer to obtain consistency in the fees until it is added.The surface, as described in detail above, the primer layer should be applied. Concrete must be placed on a layer of primer before drying.

FIAP in Industrial Flooring Construction:

Preparation of concrete: Suitable gradasyondaki 1 m3 aggregate, at least 380 kg of cement, 85 kg of water, 3 kg BINDER ® 5 and 6 kg mixed MELMENT ® L 10/33. Pre-prepared slip to the floor with the help of appropriate tools are applied. Applied primer allowed to dry ground by spreading BINDER ® 5'li fees apply.

Coating of mortar: Suitable gradasyondaki 1 m3 aggregate, 250 kg of cement and 3 kg BINDER ® 5 with a suitable amount of water in the mix. Flooring materials prepared with blended mortar is applied to the floor.

Spreading of mortar: Suitable gradasyondaki 1 m3 of river sand, 350 kg of cement and 10 kg BINDER ® 5 is mixed, add water until consistency boza. 12 hours once moistened and dry surface is expected to be applied with sprinkling equipment. Plaster or ceramic floor surfaces before application will be dampened, then the application is made.

Drying Time: BINDER ® 5 was prepared with the contribution of cement-based screed can walk over 24 hours later.
BINDER resistance at +20 ° C ® 5 Pieces fees 28 days after the end wins.

Conformance with other additives for cement fiaplarda 350 kg, 4 kg BINDER ® 5 and 5 kg available MELMENT ® L 10/33.

Being used MELMENT ® L 10/33, BINDER ® 5 'in the mechanical properties of cement-based mixtures with high percentage increases in running. Both contributions also should be added to the mixture separately.

Cleaning of tools: application of the instruments used must be cleaned immediately with water.

Packaging

10 kg and 30 kg cans

Storage: Unopened in original packaging, closed and must be stored in places away from direct sunlight. Short-term storage, should be placed on top of more than 3 pallets and shipping must be done first in, first out system.
Long-term storage, the pallets should be placed on top.

Shelf Life: appropriate storage conditions, shelf life is 12 months from date of manufacture.Closing the lid of the packaging has been opened along the shelf life can be used.

Security Measures: During application, Work and Health to conduct appropriate business suits, protective gloves, goggles and masks should be used. During storage and application to the skin and eyes should not be in contact, in case of contact, rinse immediately with soap and water, should contact a doctor immediately in case of swallowing. Application areas of food and beverage materials should not be inserted. Must be stored out of the reach of children. For details of the Safety Data Sheet (Material Safety Data Sheet) should be viewed.